Determining the Optimal Injection Molding Process Parameters by Response Surface Methods

QR Code

Determining the Optimal Injection Molding Process Parameters by Response Surface Methods

The difficulty in adjusting optimum process parameters setting may cause defects on injected molded parts such as shrinkage. In this study the author wants to determine the optimal injection molding process parameters which will minimize the shrinkage defect on a plastic cell phone housing component...

Full description

Bibliographic Details
Main Author:	Rajalingam, Sokkalingam
Other Authors:	Organizing Commitee, 8th CUTSE International Conference 2013
Format:	Conference Paper
Published:	8th CUTSE International Conference 2013 2013
Subjects:	RSM target value and model shrinkage Injection moulding
Online Access:	http://hdl.handle.net/20.500.11937/35148

Similar Items

Modeling and Optimization of Injection Molding Process Parameters for a Plastic Cell Phone Housing Component
by: Rajalingam, Sokkalingam, et al.
Published: (2013)

Optimal Process Parameters Setting on Shrinkage of an Injection Molded Part using Design of Experiment Method
by: Rajalingam, Sokkalingam, et al.
Published: (2012)

A Statistical Experimental Study on Shrinkage of Injection-Molded Part
by: Rajalingam, Sokkalingam, et al.
Published: (2012)

A Study on Injection Moulding and Injection Blow Molding Technology
by: Sokkalingam, Rajalingam
Published: (2009)

A Preliminary Study on Optimizing Injection Moulding Process by Using Response Surface Method
by: Sokkalingam, Rajalingam
Published: (2009)

Determining Optimal Moulding Process Parameters by Two Level Factorial Design with Center Points
by: Sokkalingam, Rajalingam
Published: (2011)

Determining optimal moulding process parameters by two level factorial design with center points
by: Rajalingam, Sokkalingam, et al.
Published: (2012)

Identifying the Moulding Machine Parameters to Maintain the Responses within the Target Value by Design of Experiment
by: Sokkalingam, Rajalingam, et al.
Published: (2011)

Robust Part Quality by Controlling the Injection Moulding Process with 24 Fraction Factorial Design: A Case Study
by: Sokkalingam, Rajalingam
Published: (2010)

Identifying the critical moulding machine parameters affecting injection moulding process by basic statistical process control tools
by: Rajalingam, Sokkalingam, et al.
Published: (2012)

Identifying the Critical Moulding Machine Parameters Affecting Injection Moulding Process by Basic Statistical Process Control Tools
by: Sokkalingam, Rajalingam, et al.
Published: (2011)

Investigating the effect of process parameters on dimensional accuracy and ultimate tensile strength of micro injection moulded micro parts
by: Mani, Mohammad Reza
Published: (2016)

An investigation into the thermal management and control of ceramic injection moulding die-tools
by: Bianchi, Maria Floriana
Published: (2020)

Optimization of injection molding parameter in processing polypropylene using Taguchi method / Mohamad Adib Adam Abd Wahab
by: Abd Wahab, Mohamad Adib Adam
Published: (2017)

Focused ion beam milling of brass for microinjection mould fabrication
by: Vladov, Nikola, et al.
Published: (2011)

Optimization of Dissolved Oil Separation for Produced Water Analysis
by: Khor, Ee-Huey, et al.
Published: (2010)

Injection Molding of Stainless Steel (SUS 316L) Powder Using a Thermoplastic Binder System
by: Ibrahim, Rosdi
Published: (2002)

Perceptions of risk and safety within injection settings: Injection drug users' reasons for attending a supervised injecting facility in Vancouver, Canada
by: Small, W., et al.
Published: (2012)

Development of inconel 718 parts produced by metal injection molding technique for aerospace application
by: Suleiman @ Ahmad, Muhammad Jabir
Published: (2019)

Compression moulding of composites with hybrid fibre architectures
by: Corbridge, D.M., et al.
Published: (2017)

Optimization of process parameters of injection moldings for plastic pallets manufacturing industry
by: Vivekanandan, Panneerselvam, et al.
Published: (2019)

Rates of injection in prison in a sample of Australian injecting drug users
by: Fetherston, James, et al.
Published: (2013)

The sensitivity of diesel engine performance to fuel injection parameters at various operating points
by: Gambrill, Richard
Published: (2004)

Strategies to control the high temperature shrinkage of fly ash based geopolymers
by: Vickers, Les, et al.
Published: (2014)

Design, Analysis and Fabrication of Plastic Injection Mould for Tensile Test Specimen
by: Mohd Ariffin, Mohd Khairol Anuar
Published: (2001)

Modelling the effects of textile preform architecture on permeability
by: Wong, Chee Chiew
Published: (2006)

Research note: Laboratory study of the influence of changing the injection rate on the geometry of the fluid front and on P-wave ultrasonic velocities in sandstone
by: Lopes, Sofia, et al.
Published: (2012)

Translational considerations in injectable cell-based therapeutics for neurological applications: concepts, progress and challenges
by: Amer, Mahetab H., et al.
Published: (2017)

Duration of subcutaneous heparin injections : effect on bruising and pain.
by: Chan, Harriet S. C.
Published: (2000)

Effect of dimensional parameters on warpage of injection-molded plastic part using response surface methodology
by: Mohd Nasri, Md Salim
Published: (2009)

Shrinkage Behaviour of Cement-Treated Crushed Rock Base in Western Australia
by: Jitsangiam, Peerapong, et al.
Published: (2014)

Injectivity and quantification of capillary trapping for CO2 storage: A review of influencing parameters
by: Raza, A., et al.
Published: (2015)

Development of a conceptual model for the ultra-fine particulate matter processes in gasoline direct injection engines using integrated CFD-chemical kinetic modelling
by: Tan, Jing Yang
Published: (2020)

Warpage analysis on thick shell part using response surface methodology (RSM) and bat algorithm (BA) to optimize parameter setting in injection molding process
by: Ch'Ng, S. Q., et al.
Published: (2018)

Optimization of injection molding parameters for WC-TaC-6Co
by: Prathabrao, M., et al.
Published: (2019)

Characterization on insulation performance, poststability, and foaming process of rigid polyurethane sandwich panel for cold storage warehouse
by: Xu, Jie, et al.
Published: (2017)

Compression moulding of hybrid carbon fibre composites for structural applications
by: Corbridge, David Michael
Published: (2018)

The incidence of feline injection site sarcomas in the United Kingdom
by: Dean, Rachel S., et al.
Published: (2013)

Optimization of injection molding and solvent debinding parameters of stainless steel powder (SS316L) based feedstock for metal injection molding
by: Muhammad Ilman Hakimi Chua,, et al.
Published: (2013)

The relationship between age and risky injecting behaviours among a sample of Australian people who inject drugs
by: Horyniak, Danielle, et al.
Published: (2013)