Effect of Additional Factors on Dimensional Accuracy and Surface Finish of Turned Parts

QR Code

Effect of Additional Factors on Dimensional Accuracy and Surface Finish of Turned Parts

This paper reports the experimental and analytical results of an investigation of additional factors that affect the dimensional accuracy and surface finish of turned parts besides the three major cutting parameters—cutting speed, feed rate, and depth of cut. The selected additional factors were coo...

Full description

Bibliographic Details
Main Author:	Islam, Mohammad Nazrul
Format:	Journal Article
Published:	Taylor and Francis 2013
Subjects:	Dry turning blank size flood turning Pareto ANOVA Taguchi method minimum quantity lubrication (MQL) turning
Online Access:	http://hdl.handle.net/20.500.11937/30748

Similar Items

Effect of Cutting Fluid Supply Strategies on Surface Finish of Turned Parts
by: Islam, Mohammad Nazrul, et al.
Published: (2011)

Comparison of Dry and Flood Turning in Terms of Dimensional Accuracy and Surface Finish of Turned Parts
by: Rafai, Noor, et al.
Published: (2011)

Effect of cooling methods on dimensional accuracy and surface finish of a turned titanium part
by: Islam, Mohammad Nazrul, et al.
Published: (2013)

Effect of Amount of Cutting Fluid on Surface Finish of Turned Parts
by: Islam, Mohammad Nazrul
Published: (2011)

An Investigation of Surface Finish in Dry Turning
by: Islam, Mohammad Nazrul, et al.
Published: (2011)

Effect of tool geometry on dimensional accuracy and surface finish of turned parts
by: Islam, Mohammad Nazrul, et al.
Published: (2013)

Development of Machine Learning Algorithm for Acquiring Machining Data in Turning Process
by: Ali Al-Assadi, Hayder M. A.
Published: (2004)

Reduction of amount of cutting fluid in flood turning by finite element analysis
by: Islam, Mohammad Nazrul, et al.
Published: (2012)

Dimensional Accuracy Achievable in Wire-cut Electrical Discharge Machining
by: Islam, Mohammad Nazrul, et al.
Published: (2011)

Unfinished Turns in French: How Context Matters
by: Chevalier, Fabienne HG
Published: (2008)

Ductile mode turning of brittle materials and its practical aspects
by: Pramanik, Alokesh, et al.
Published: (2013)

The impact of impulsive voltage waveforms on the electrical insulation of actuators for more electrical aircraft (MEA)
by: Cavallini, Andrea, et al.
Published: (2017)

Their Dreams and Ours: Britten, Film, and 'The Turn of the Screw'
by: Auker, Peter Leslie Roy
Published: (2021)

Ultra-precision machining of electroless nickel plated die materials
by: Pramanik, Alokesh, et al.
Published: (2002)

Cutting performance of diamond tools during ultra–precision turning of electroless nickel plated die materials
by: Pramanik, Alokesh, et al.
Published: (2003)

Non-linear circuit based model of PMSM under inter-turn fault: a simple approach based on healthy machine data
by: Belguerras, Lamia, et al.
Published: (2016)

Turn-turn short circuit fault management in permanent magnet machines
by: Arumugam, Puvaneswaran, et al.
Published: (2015)

Gesture bike: examining projection surfaces and turn signal systems for urban cycling
by: Dancu, Alexandru, et al.
Published: (2015)

Gesture bike: examining projection surfaces and turn signal systems for urban cycling
by: Dancu, Alexandru, et al.
Published: (2015)

Effect of Machining Conditions and Phosphorus Content in Nano-Precision Machining of Electroless Nickel
by: Pramanik, Alokesh, et al.
Published: (2003)

A falling of the veils: turning points and momentous turning points in leadership and the creation of CSR
by: Hemingway, Christine A., et al.
Published: (2018)

Propaganda and persuasion: political discourse and the negotiation of power and authority in Yorkist and early Tudor England
by: Wheddon, Rebecca
Published: (2024)

Railway network resilience
by: Meesit, Ratthaphong
Published: (2019)

Feasibility Study of Adopting Minimal Quantities of Lubrication for End Milling Aluminium
by: Boswell, Brian, et al.
Published: (2012)

An Experimental Approach to Determine the Effectiveness of Minimum Liquid Cooling for End Milling 1040 Steel
by: Boswell, Brian
Published: (2010)

The Effect of Combined Cold Air and Minimum Liquid Cooling on End Milling
by: Boswell, Brian, et al.
Published: (2011)

The challenge of adopting minimal quantities of lubrication for end milling aluminium
by: Boswell, Brian, et al.
Published: (2013)

Advancing Environmentally Conscious Machining
by: Ginting, Yogie, et al.
Published: (2015)

A modified modulation scheme for three-level diode-clamped matrix converter under unbalanced input conditions
by: Su, Mei, et al.
Published: (2018)

Polyol esters as thinner and biolubricant additive for synthetic-based drilling fluid
by: Kania, Dina
Published: (2019)

Environmental friendly cutting fluids and cooling techniques in machining: a review
by: Debnath, Sujan, et al.
Published: (2014)

Development of dry film lubricants for highly loaded contacts
by: Barman, Kanika
Published: (2016)

Improving the management of inventory in the Rolls-Royce Energy Aftermarket Business
by: Palmer, John
Published: (2011)

Synthesis of jatropha biolubricant using sodium methoxide as catalyst
by: Gunam Resul, Mohamad Faiz Mukhtar
Published: (2012)

Biodegradation of phenanthrene and pyrene using bacteria isolated from used vehicle lubricant-contaminated soil
by: Darma, Umar Zubairu
Published: (2017)

Analisa ke atas minyak pelincir / Razak Awang … [et al.]
by: Awang, Razak, et al.
Published: (1997)

Oil film behaviour in hydrodynamic lubrication of journal bearing / Mohamad Ali Ahmad
by: Ahmad, Mohamad Ali
Published: (2014)

Surface texturing on dry-lubricated transmissions and power systems to deliver better performance and simplified systems in aerospace engineering
by: Ding, Liang
Published: (2021)

The synthesis of orthoesters and their role as delivery systems for lubricant additives
by: Roy, Charlotte
Published: (2020)

The Use of Bills of Quantities in Construction Projects - An Australian Survey
by: Davis, Peter, et al.
Published: (2004)