Gas-solid flow hydrodynamics of an industrial scale catalyst lift engager

QR Code

Gas-solid flow hydrodynamics of an industrial scale catalyst lift engager

This study characterizes the hydrodynamics of an industrial scale lift engager which circulates the catalyst between the reactor and regenerator sections of a continuous catalytic reformer in an oil refinery. The flow of Geldart D particles in this unit was simulated using a granular Eulerian model....

Full description

Bibliographic Details
Main Authors:	Shah, Milinkumar, Mayne, J., Utikar, Ranjeet, Tade, Moses, Pareek, Vishnu
Format:	Journal Article
Published:	Elsevier BV 2010
Subjects:	Gas–solid flow modelling Eulerian–Eulerian approach Lift engager Frictional pressure Drag
Online Access:	http://hdl.handle.net/20.500.11937/29815

Similar Items

Hydrodynamics of an FCC riser using energy minimization multiscale drag model
by: Shah, Milinkumar, et al.
Published: (2011)

Verification of EMMS formulation using lattice Boltzmann simulations
by: Shah, Milinkumar, et al.
Published: (2014)

Effect of a cluster on gas–solid drag from lattice Boltzmann simulations
by: Utikar, Ranjeet, et al.
Published: (2013)

Hydrodynamic study of catalyst lift engager
by: Shah, Milinkumar, et al.
Published: (2009)

Multiphase Transient Flow in Pipes
by: Ben Mahmud, Hisham
Published: (2012)

Hydrodynamics of catalyst lift engager using eulerian granular model
by: Shah, Milinkumar, et al.
Published: (2008)

Numerical simulations of liquid-gas-solid three-phase flows in microgravity
by: Zhang, Xinyu, et al.
Published: (2012)

CFD simulation of solid–liquid stirred tanks
by: Wadnerkar, Divyamaan, et al.
Published: (2012)

Experimental investigation of gas lift technique in viscous fluids
by: Ibrahim, Abubakr
Published: (2017)

A study of erosion phenomena in coal fired furnace using CFD modelling
by: Gandhi, Mikilkumar Bansilal
Published: (2010)

Turbulent drag reduction using surface plasma
by: Jukes, Timothy N.
Published: (2007)

Tribology of thin wetting films between bubble and moving solid surface
by: Karakashev, S.I., et al.
Published: (2014)

A Plate Type Edge-Lift Anchor: Panel Reinforcement Influence on Failure Loads
by: Barraclough, Andrew, et al.
Published: (2012)

Hydrodynamics of slug flow in capillary microchannels
by: Bhatelia, Tejas, et al.
Published: (2009)

Hydrodynamics of liquid films on horizontal spinning disc
by: Bhatelia, Tejas, et al.
Published: (2009)

Investigation of large-scale structures in turbulent boundary layer and their detections by wall-based sensors array
by: Rkiouak, Noura
Published: (2020)

Simulation and Analysis of Carbon-in-Leach (CIL) Circuits
by: Wadnerkar, Divyamaan, et al.
Published: (2012)

Particle deposition in natural gas pipelines using computational fluid dynamics modelling
by: Veluswamy, Ganesh, et al.
Published: (2012)

EMMS model for high solid flux riser flows
by: Utikar, Ranjeet, et al.
Published: (2009)

A Plate Type Edge-Lift Anchor: Shear Reinforcement Influence on Failure Loads
by: Barraclough, Andrew, et al.
Published: (2012)

Potential Application of Downhole Gas Compressor to Improve Productivity for Gas Reservoir
by: Hossain, Mofazzal, et al.
Published: (2013)

Hydrodynamic Simulation of Cyclone Separators
by: Utikar, Ranjeet, et al.
Published: (2010)

Torque and drag modelling for Redhill South-1 in Northern Perth Basin, Australia
by: Smith, S., et al.
Published: (2012)

Development of predictive model for stoop and squat postures on physiological and psychophysical responses in manual lifting tasks
by: Kamarudin, Nor Hafeezah
Published: (2019)

Modelling of the interaction between a falling n-heptane droplet and hot solid surface
by: Gumulya, M., et al.
Published: (2014)

Simultaneous estimation of states and inputs in a planar solid oxide fuel cell using nonlinear adaptive observer design
by: Vijay, Periasamy, et al.
Published: (2013)

Hydrodynamics of viscous slug flow in inclined pipes
by: Dafyak, Longtong
Published: (2023)

A Plate Type Edge-Lift Anchor: Influence of Reinforcing Configurations on Failure Loads
by: Barraclough, Andrew, et al.
Published: (2011)

Core lifting task assessment using time-frequency distribution of surface electromyogram signal
by: Shair, Ezreen Farina
Published: (2019)

CFD study: Effect of pulsating flow on gas-solid hydrodynamics in FCC riser
by: Shah, Milin, et al.
Published: (2016)

Effect of inlet boundary conditions on computational fluid dynamics (cfd) simulations of gas-solid flows in risers
by: Shah, Milinkumar, et al.
Published: (2012)

Simulation of gas–solid flows in riser using energy minimization multiscale model: Effect of cluster diameter correlation
by: Shah, Milinkumar, et al.
Published: (2011)

Effect of a cluster on gas-solid drag from lattice boltzmann simulations
by: Shah, Milinkumar, et al.
Published: (2012)

Hydrodynamic study of fluid catalytic cracker unit stripper
by: Veluswamy, Ganesh, et al.
Published: (2013)

Mechanical characterization of AA6061-T6 aluminum alloy friction stir and tungsten arc welded with and without post-weld heat treatment
by: Fadaeifard, Firouz
Published: (2016)

Application of downhole gas compression to improve productivity for depleted natural gas reservoir
by: Ismail, M., et al.
Published: (2013)

Coarse grid simulation of gas-solid flows in riser
by: Shah, Milinkumar T.
Published: (2011)

Drag reduction in turbulent channel flow using bidirectional wavy Lorentz force
by: Huang, LePing, et al.
Published: (2014)

Computational modeling of high solid flux riser flows
by: Utikar, Ranjeet, et al.
Published: (2009)

Hydrodynamics of a Fluid Catalytic Cracking Stripper Using γ-ray Densitometry
by: Veluswamy, Ganesh, et al.
Published: (2011)