Simulation of the cutting action of a single PDC cutter using DEM

QR Code

Simulation of the cutting action of a single PDC cutter using DEM

Optimization of costly drilling operations is essential to reduce the overall costs of oil and gas extraction. Simulation of these operations can yield a better selection of parameters for maximum drilling efficiency. One of the most cost efficient methods to do so is by computer modeling. Because o...

Full description

Bibliographic Details
Main Authors:	Joodi, B., Sarmadivaleh, Mohammad, Rasouli, V., Nabipour, A.
Format:	Conference Paper
Published:	2012
Online Access:	http://hdl.handle.net/20.500.11937/27992

Similar Items

Simulation of the cutting action of a single PDC cutter using DEM
by: Joodi, B., et al.
Published: (2012)

Investigation into the impacts of rock/cutter interface geometry on drilling response of PDC cutters
by: Doshvarpassand, Siavash
Published: (2017)

Analysis of rock cutting process with a blunt PDC cutter under different wear flat inclination angles
by: Rostamsowlat, I., et al.
Published: (2018)

Identification of Porosity Damaged Zones around a Perforation Tunnel Based on DEM Simulation
by: Sarmadivaleh, Mohammad, et al.
Published: (2010)

Finite Element Simulation of Downhole Stresses in Deep Gas Wells Cements
by: Nabipour, Amin, et al.
Published: (2010)

A DEM Study on Perforation Induced Damaged Zones and Penetration Length in Sandstone Reservoirs
by: Nabipour, Amin, et al.
Published: (2010)

Steps for conducting a valid hydraulic fracturing laboratory test
by: Sarmadivaleh, Mohammad, et al.
Published: (2013)

Three dimensional numerical modelling of joint spacing and orientation effects on rock cutting process by a single TBM cutter
by: Sharifzadeh, Mostafa, et al.
Published: (2009)

Comparative study on conductivity using Polarization and Depolarization Current (PDC) test for HV Insulation
by: Jamaii, N. A. M., et al.
Published: (2011)

Designing portable circular cutter tools using inventors for straight cutting iron at welding workshop
by: Mohd Alwi, Abg, et al.
Published: (2021)

DEM-CFD Simulations for Various Fluidizations
by: Azri, Alias, et al.
Published: (2014)

Effect of cutter and rock properties on the frictional contact in rock cutting with blunt tools
by: Rostam Sowlat, Iman
Published: (2017)

Some challenges in hydraulic fracturing of tight gas reservoirs: An experimental study
by: Rasouli, Vamegh, et al.
Published: (2011)

Simulation of hydraulic fracturing in tight formations
by: Sarmadivaleh, Mohammad, et al.
Published: (2010)

A motorized cutter
by: Misron, Norhisam, et al.
Published: (2011)

Spider Grass Cutter
by: Zahar, Mohd Muzaffar, et al.
Published: (2020)

Numerical simulations of hydraulic fracture intersecting an interbed of sandstone
by: Sarmadivaleh, Mohammad, et al.
Published: (2012)

Automated grass cutter using voice recognition
by: Muhamad Salihin, Nasir, et al.
Published: (2021)

DEMs and SAR Images
by: Teng, H.-T., et al.
Published: (2006)

Prediction of remaining useful life of an end mill cutter
by: Seow, Xiang Yuan
Published: (2016)

Design and fabrication of motorized cutter prototype
by: Mohamad Ruzaini, Mohamed Ibrahim
Published: (2013)

Simulations of fluid flow through a porous formation with a single rough fracture plane
by: Rasouli, A., et al.
Published: (2012)

Peranan perhubungan awam dalam program perhubungan komuniti : kajian kes di Perbadanan Pembangunan Pulau Pinang (PDC)
by: Hassan, Wazharatul Fajariyyah
Published: (2004)

A micromechanical study of unsaturated granular material using DEM simulation and X-ray CT
by: Zeng, Guohan
Published: (2018)

Development of DEM-CFD Simulation of Combustion Flow in Incinerator with the Representative Particle Model
by: Kuwagi, Kenya, et al.
Published: (2016)

Development of cutter for printed circuit board using hydraulic principle
by: Mohd Muhaymin, Ismail
Published: (2007)

Smart cutter bantu pekebun kelapa sawit
by: Zahrom, Basir
Published: (2012)

Development of automatic control oil palm cutter
by: Abdul Rahim, Rahimi, et al.
Published: (1999)

Pemotong e-cutter mudahkn kerja mencantas
by: Sinar Harian
Published: (2018)

Design and improvise of high reach wire cutter
by: Esam, Asrizam, et al.
Published: (2022)

Morphological segmentation of physiographic features from DEM
by: Sathymoorthy, D., et al.
Published: (2007)

The Wear Pattern of Router Cutter Material Between High Speed Steel and Solid Tungsten Carbide in Cutting Rubberwood Medium Density Fiberboard
by: Bakeri, Ahmad Bahtiar
Published: (2002)

Coal cleat closure during supercritical CO2 injection and associated permeability drop: From microscale observation to DEM predictions
by: Zhang, Y., et al.
Published: (2017)

Test Design and Sample Preparation Procedure for Experimental Investigation of Hydraulic Fracturing Interaction Modes
by: Sarmadivaleh, Mohammad, et al.
Published: (2014)

Non-vibrate palm oil tree harvesting cutter using DC motor
by: Zamzuri, Hamedon, et al.
Published: (2022)

Investigating the micro mechanics of cemented sand using DEM
by: de Bono, John P., et al.
Published: (2015)

DEM of triaxial tests on crushable sand
by: de Bono, John P., et al.
Published: (2014)

Linear and nonlinear approach for DEM smoothening
by: Dinesh, S., et al.
Published: (2006)

Application of DEMs in Geo-hazard Modeling
by: Akbari, Abolghasem
Published: (2016)

Experimental and numerical investigation of the effect of inner and outer boundary dimensions on collapse of the sample in thick-walled cylinder test
by: Tehrani, S., et al.
Published: (2017)