The spur planetary gear torsional stiffness and its crack sensitivity under quasi-static conditions

QR Code

The spur planetary gear torsional stiffness and its crack sensitivity under quasi-static conditions

The sun-planet and ring-planet tooth mesh stiffness variations and the resulting transmission errors are the main internal vibration generation mechanisms for planetary gear systems. This paper presents the results of torsional stiffness analysis of involute spur planetary gear systems in mesh using...

Full description

Bibliographic Details
Main Authors:	Xue, S., Entwistle, R., Mazhar, Ilyas, Howard, Ian
Format:	Journal Article
Published:	Elsevier 2016
Online Access:	http://hdl.handle.net/20.500.11937/12124

Similar Items

The torsional stiffness of involute spur planetary gears
by: Xue, S., et al.
Published: (2015)

Torsional vibration signal analysis as a diagnostic tool for planetary gear fault detection
by: Xue, S., et al.
Published: (2018)

Calculation of the Combined Torsional Mesh Stiffness of Spur Gears with Two- and Three-Dimensional Parametrical FE Models
by: Kiekbusch, T., et al.
Published: (2011)

Vibration response from the planetary gear with flexible ring gear
by: Xue, Song, et al.
Published: (2019)

Torsional properties of spur gears in mesh using nonlinear finite element analysis.
by: Sirichai, Seney
Published: (1999)

An investigation of gear meshing behaviour of planetary gear systems for improved fault diagnosis
by: Xue, Song
Published: (2016)

Dynamic modelling of flexibly supported gears using iterative convergence of tooth mesh stiffness
by: Xue, S., et al.
Published: (2015)

Ring-planet mesh stiffness study with different boundary conditions and crack locations
by: Xue, S., et al.
Published: (2015)

Dynamic modelling of planetary gear systems for gear tooth fault
by: Wang, Zhongwei
Published: (2010)

A further study on HCR spur gears in mesh with double scope tooth profile modification
by: Wang, Jian De, et al.
Published: (2008)

Numerical and Experimental Analysis of Spur Gears in Mesh
by: Wang, Jiande
Published: (2003)

Micro Pitting And Wear Assessment Of Spur Gear
by: Abd Ghani, Muhammad Muzakkir
Published: (2022)

Investigating Bending Strength of Spur Gear : A Review
by: Ismail Ali, Hj Abdul Aziz, et al.
Published: (2016)

Finite element analysis of impact energy on spur gear
by: Ismail Ali, Abdul Aziz, et al.
Published: (2018)

Modeling Of A Surface Contact Stress For Spur Gear Mechanism Using Static And Transient Finite Element Method
by: F. R. M., Romlay
Published: (2008)

Static stiffness and stress distribution of gasoline and natural gas vehicle platforms subjected to torsion loads
by: Sahari, Barkawi, et al.
Published: (2009)

Harvesting energy from planetary gear using piezoelectric material
by: Chilabi, Haider Jaafar, et al.
Published: (2020)

Harvesting energy from planetary gear using piezoelectric material
by: Hussein, Chilabi Haider Jaafar
Published: (2019)

Modelling windage power loss from an enclosed spur gear
by: Eastwick, Carol, et al.
Published: (2007)

Design and Analysis of Tooth Impact Test Rig for Spur Gear
by: Wafiuddin, Md Ghazali, et al.
Published: (2016)

Acoustic Emission and Specific Film Thickness for Operating Spur Gears
by: Raja Hamzah, R. I., et al.
Published: (2007)

Computational investigation of flows and pressure fields associated with spur gear meshing
by: Baydu, C. Al, et al.
Published: (2014)

Torsional stiffness matrix of non-prismatic beam elements
by: Sulaeman, Erwin
Published: (2011)

Effect of pre-seted residual stress on the spur gear / Alfonso Muze Jerol
by: Jerol, Alfonso Muze
Published: (2003)

Factor analysis on spur gear failure using computational simulation / Emilia Norazmi
by: Emilia, Norazmi
Published: (2021)

Analysis of a spur gear in automative system using finite element software
by: Mohd Khairi, Mohammad
Published: (2013)

Tooth bending stress and tooth impact stress of thin-rimmed spur gear
by: Ismail Ali, Abdul Aziz
Published: (2022)

Said-Ball Cubic Transition Curve And Its Application To Spur Gear Design
by: Yahaya, Saifudin Hafiz
Published: (2015)

Maximum torque of combination threats for spur gear based on AGMA and JGMA standards
by: Wu, Jia Hang
Published: (2014)

Crack propagation trajectory for kenaf fibre composite under quasi static loading
by: Nurul Alya Zahari, Nurul Alya Zahari, et al.
Published: (2020)

Cavitation Sensitivity Parameter Analysis for Centrifugal Pumps Based on Spectral Methods
by: McKee, Kristoffer, et al.
Published: (2015)

A vibration cavitation sensitivity parameter based on spectral and statistical methods
by: McKee, Kristoffer, et al.
Published: (2015)

Parametric transition as a spiral curve and its application in spur gear tooth with FEA
by: Yahaya, S.H, et al.
Published: (2011)

Cavitation sensitivity parameter analysis for centrifugal pumps based on spectral methods
by: McKee, Kristoffer, et al.
Published: (2015)

Comparative study of conventional and micro WEDM based on machining of meso/micro sized spur gear
by: Ali, Mohammad Yeakub, et al.
Published: (2010)

Spur gear tooth design and transition curve as a spiral using cubic trigonometric Bezier function
by: Wasim, Muhammad Abbas, et al.
Published: (2011)

A Mechanism of Hot-spots Formation at the Crack Tip of Al-PTFE under Quasi-static Compression
by: Feng, B., et al.
Published: (2017)

Investigating Effects of Rim and Web Thicknesses on Root Stress of Thin-rimmed Spur Gear with Symmetric Web Arrangement
by: Ismail Ali, Abdul Aziz, et al.
Published: (2017)

The Development of Lumped Mass Dynamic Modeling Methods of Planetary Gearbox for Fault Detection and Diagnosis
by: Wang, Zhongwei, et al.
Published: (2010)

Quasi-static characterisation of asphalt mixtures
by: Dunhill, Stuart Thomas
Published: (2002)

Cannot write session to /tmp/vufind_sessions/sess_1oc5j9m7timvpk8fpkbne6ip6n